Make Calls From Notification Center With TelOnNotification

Summary : This is a nice Notification Center widget that lets you make calls.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

This is a nice Notification Center widget that lets you make calls.
You have an iPhone, but where's the Phone? Is it on your home page, your second page, your third page? Is it on your dock? I don't know! Well now, you never have to not know again. If you need to make a call but you find that looking for your Phone application is a pain in the rear, then you'll appreciate this new jailbreak widget for Notification Center that allows you to make phone calls but sliding down Notification Center, entering a phone number, and tapping the call button. This widget is free and has been dubbed TelOnNotification by iOS developer timetravel0.
The widget has a decent looking GUI (graphical user interface). There have been a lot of widgets that are completely atrocious compared to the way that we might expect Apple to implement a widget. This one keeps it nice and simple and best of all, it's small. It doesn't take up a ton of room. Before you actually start typing in a phone number to dial, the widget looks as it does in the screenshot below:

After you tap on that bar that says, "Telephone number to call" the iOS number pad appears with a call button in the bottom left. The number pad is demonstrated by the first image in this review. It looks very eye-candy-ish and I'm sure that a lot of people if not most would like to add this widget to their collection for iOS 5's Notification Center.
There are some prerequisites to using it. For example, you cannot dismiss the number pad easily when you are in Notification Center. You have to press the home button, which exits Notification Center completely, just to put the number pad away. So this means that you shouldn't tap on the widget unless you really want to make a call otherwise that number pad will get in the way of you viewing your other widgets. Another thing is that you need to know someone's phone number by heart, otherwise you won't be able to call them. This widget doesn't support address book integration, so you can't go through your Contacts application and pick a contact that you've added in the past to call.
Do those prerequisites make it useless? Absolutely not. It's still a quick way to dial a phone number if you don't want to fumble around for your Phone application. You will need to be running iOS 5 to download this widget because it depends on Notification Center to function. You can enable the widget or disable it at any time by simply dragging it in and out of Notification Center in the Settings application under 'settings>notifications>in notification center'. I think this is a nice thing to have if you're an iPhone power-user like me.

via modmyi via iDownloadBlog

Read more »

App of Today: TPS Star Warfare:Alien Invasion

Summary : Star Warfare:Alien Invasion third-person shooters game is just available for iPhone. The story takes place on an alien planet, UBW-594244, where a revolutionary raw material is found. Life is all good and well until the enemies appear, and as always, you’re their last hope.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

Star Warfare:Alien Invasion third-person shooters game is just available for iPhone. The story takes place on an alien planet, UBW-594244, where a revolutionary raw material is found.  Life is all good and well until the enemies appear, and as always, you’re their last hope.
Star Warfare features 30 levels spread across 5 maps, various enemies and ‘console-like smooth control’.  You can pick from 26 weapons and upgrade them 8 times each.  There’s also co-op multiplayer with support for up to 3 players per team.
Description
 Defeat 'them', now, or lose your home forever!
 Console-quality boss battles, 30 single player levels, multiplayer supported, tons of gear and unique avatars to collect!!
 UBW-594244 is a beautiful and peaceful planet located at the far edge of human territory...
 Mithril, a revolutionary new raw material, is found here. The population is growing rapidly. It's a happy and wealthy region,
 ...Until 'they' appear!
 There's nowhere to retreat: Defeat the enemies here, now, or your home will be lost forever!
 Prototype-02, a humanoid war machine, was released by our top scientists.
 And now, as always, our last hope...
 Is YOU!
 Solid single player mode
 l Various enemies with rich AI
 l Console-like smooth control
 l 5 maps and 30 levels, loot can be used in solo and multiplayer modes
 Simply the best co-op shooting game on smart phones
 l Console-quality boss battles, team with up to 3 players.
 l Earn more gold in team survival mode.
 l Armor and bags specially designed for team battle
 Rich and flexible gear system
 l 26 weapons, each upgradable 8 times, unlocked as you promote up the ranks.
 l Eight Suits, each part with special attributes, a whole collection provides extra bonus. Elite suite entitles an extra special buff.
 l Mix&match weapons with suits to earn additional damage
 l 14 military bags with special functions

download

Read more »

Must-have Cydia Tweak For Siri on Your iPhone 4S and Spire Devices

Summary : Now we have got Spire and jailbroken iPhone 4S, if you are telling me you are using Siri just like sending an email or setting up a reminder, then you are so wasting your jailbroken device. So we got you these must-have Cydia tweak to make your Siri more powerful.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

 

Now we have got Spire and jailbroken iPhone 4S, if you are telling me you are using Siri just like sending an email or setting up a reminder, then you are so wasting your jailbroken device. So we got you these must-have Cydia tweak to make your Siri more powerful.
Hands-Free Control

The Hands-Free Control Cydia tweak will allow you to activate your virtual personal assistant by simply speaking out loud “Siri”. The way this Cydia tweak works is by constantly listening for the voice command Siri as a background process. Due to the fact that this Cydia tweak is constantly running in the background it does have slight effects on your battery life, but nothing too outrageous. Another neat feature to this tweak is it allows Siri to prompt you with “Yes?” upon being activated.
Read more
SiriToggles

The SiriToggles Cydia tweak is sort of like SBSettings for Siri. Upon installing SiriToggles you will be able to toggle numerous system-wide settings like Airplane Mode, WiFi and Cellular Data. Additionally you will be able to launch applications, reduce the screen brightness and even check your battery level. The Siri Toggles Cydia tweak will seriously extend the functionality of Siri!
Read more
VoiceUtils

The VoiceUtils Cydia tweak will very simply grant Siri the ability to reboot, restart SpringBoard, enter safe mode and power off your iOS device. An additional feature this Cydia tweak provides is the ability to launch applications. If you are just after this feature, however, I would install the SiriToggles Cydia tweak instead.
Read more
Sireet

The Sireet Cydia tweak will allow you to tweet directly from Siri. My only gripe with this Cydia tweak is that there is no confirm to send option. The reason I think there should be such an option is due to the fact that occasionally Siri mispronounces words. Thus, it would be nice if I noticed an error I could stop Siri from tweeting that specific tweet and allow me to I re-say my tweet.
Read more
AssistantExtensions

The Cydia tweak AssistantExtensions, gives Siri much more power than what it has now. It’s not just a tweak, but it is a framework that increases the possibilities of what can be done using Siri. The AssistanExtensions Cydia tweak is based upon MobileSubstrate and can be used to control a lot of things on your iPhone 4S. For example you can tweet, launch apps, set the screen brightness, generate random numbers, toggle system settings and so much more. If you are looking to a Cydia tweak to combine the features of tweaks such as SiriToggles, VoiceUtils and Sireet then AssistantExtensions is the tweak for you!
Read more
Lingual

The Lingual Cydia tweak allows you to translate words or phrases to over 30 different languages using Siri. This is extremely useful if you are traveling abroad or simply are dying to know how to say certain things in another language.
Read more
Custom Siri Background

The Custom Background Cydia tweak will allow you to go into the Settings.app and select an image from your Photo Library or even take a picture directly from the Camera.app to use as Siri’s new background.
Read more
Siri Mic Colors

The Siri Mic Colors Cydia tweak allows you to easily change the Siri mic icon that appears when you activate Siri. For example, you can change the boring old Siri mic icon to a green icon, a yellow icon, a red icon and even blue icon.
Read more
In this article we ended up listing almost all of the available Siri Cydia tweaks, but at this time, because there are not many Siri Cydia tweaks available, we thought it would be worth your while to look through them. Did we miss any? Do you have any thoughts you would like to share? Let us know in the comments section below…
via ijailbreak

Read more »

Apple Really Care About Labor Abuses ? YES !

Summary : Foxconn, is not the only where the Apple products come from, but is the place that the explosion, workers serial suicide and labor abuses happens, so some people call it bloody factory, we're using blooding iDevices, about this, Apple CEO Tim Cook sent out a lengthy email to all of his employees that is a direct response to the recent reports of factory worker mistreatment. Cook’s message comes after The New York Times published the inside stories of working conditions in China factories which make parts or assemble Apple iPhone and iPad. Cook said, “We care about every worker in our worldwide supply chain” …

• PandaApp Editor

• Current Device: iPhone 3GS, Omnia 7, iPad 1
• Future Device: iPhone 5
• Introduction:Techni-Geek live a life in Technicolor!

Foxconn, is not the only where the Apple products come from, but is the place that the explosion, workers serial suicide and labor abuses happens, so some people call it bloody factory, we're using blooding iDevices, about this, Apple CEO Tim Cook sent out a lengthy email to all of his employees that is a direct response to the recent reports of factory worker mistreatment. Cook’s message comes after The New York Times published the inside stories of working conditions in China factories which make parts or assemble Apple iPhone and iPad. Cook said, “We care about every worker in our worldwide supply chain” …

The New York Times published a lengthy report with details about the harsh conditions of working in the factories of Apple product manufacturer. The report recalls the two explosions at iPad factories last year that killed four people and 77 workers injured. In addition, a former Foxconn executive said that Apple never cared about anything other than increasing their product quality and decrease the production cost. Another former Apple executive claimed that Apple knew about the labor abuses in China for four years, but the company still choose to go on. The main reasons is because Apple think that the system works for them, and they have actually became the one who force the China factories to cut safety.

These reports clearly hit Tim Cook’s sensitive nerve and he has responded the issue. Before Cook was promoted to become chief operating officer in 2004, Cook is credited with restructuring Apple’s manufacturing operations, completely farm out the work to third-party manufacturers and created the supply chain in China. This could explain why Cook has to clarify immediately on the mistreatment of factory workers. Here are the key points of his reply email:

“Any accident is deeply troubling, and any issue with working conditions is cause for concern. Any suggestion that we don’t care is patently false and offensive to us”
“Every year we inspect more factories, raising the bar for our partners and going deeper into the supply chain. We’ve made a great deal of progress and improved conditions for hundreds of thousands of workers … We will continue to dig deeper, and we will undoubtedly find more issues …”
“We are focused on educating workers about their rights, so they are empowered to speak up when they see unsafe conditions or unfair treatment …”
“We know of no one in our industry doing as much as we are, in as many places, touching as many people … What we will not do — and never have done — is stand still or turn a blind eye to problems in our supply chain. On this you have my word.”
To advertise the commitment to worker safety, Apple has already launched a “Supplier Responsibility” page on its website early this month, which details the actions it takes towards ensuring good working conditions and environmentally-friendly production practices. Apple has also opened its doors to the Fair Labor Association for evaluations. Interestingly, Apple is the first tech company the association has ever monitored because it specializes in clothing and textile manufacturers. Right now, Apple has to go into their suppliers’ factories, which mostly own by Foxconn and make changes.

Last year, an explosion at Foxconn’s Chengdu factory tragically took the lives of four employees
It would seem that sharing profits with suppliers could be one way in which Apple could improve the working conditions in China. But this voluntary step would fly against market dynamics and there is no guarantee that suppliers would pass the benefits onto the workers. What incentive does Foxconn have to improve standards if they know full well that Apple’s entire business model relies on them ? The problem is not easy to solve. Apple is just as much to blame as the Chinese factories on labor abuses.
via micgadget

Read more »

How to Repaire a GSM iPhone 4 Screen Just By Yourself [Video]

Summary : If you don’t want to pay the extra cash for your iPhone and feel pretty confident in your repair skills, here is the walkthrough to repair an GSM iPhone 4 screen just by yourself.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

If you don’t want to pay the extra cash for your iPhone and feel pretty confident in your repair skills, here is the walkthrough to repair an GSM iPhone 4 screen just by yourself.
Disclaimer: Any opening repairing is with risk, and it's also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty. If you don’t feel comfortable opening your device, don’t. Use extreme care and caution when performing a repair on any device.
What you need for a DIY GSM iPhone 4 screen replacement
PXLFIX recommends using only quality and genuine parts from a reputable supplier like eTech Parts. They have quality parts, tools, and much more for all your repair needs.

• GSM iPhone 4 (please note there ARE internal differences between the GSM and CDMA models)
• New GSM iPhone 4 LCD & digitizer assembly
• SIM removal tool (or a paper clip)
• #00 Phillips screwdriver
• Pry tool or spudger (you may need a handheld razor blade as well)
• Security screwdriver (only if your iPhone has 5-point security screws in the dock connector)

Power off your iPhone 4

Before performing any repair, always power off your device before removing any screws or parts.
Remove the back

1. First remove the bottom 2 dock connector screws in your iPhone 4. Use either your #00 screwdriver or the five point depending on whether or not your iPhone 4 has security screws in the dock connector. Almost all newer devices will have security screws.

2. To remove the back simply slide the back upwards and lift it off gently.
3. Set the back and 2 dock connector screws aside.
Remove your SIM card
Use a SIM removal tool or a paperclip to remove your SIM card and tray. Set them aside.
Remove the battery

    1. To remove the battery you’ll need to remove the #00 screw holding the battery clip in place. Remove this screw located to the bottom left of the battery.

    2. The metal clip on the battery is what clips the battery to the logic board. You’ll need to pop this clip up with your plastic pry tool. Simply stick the end of your pry tool underneath the clip and gently pull upwards until it unfastens from the logic board.

    3. To remove the battery, I do not recommend using the plastic pull tab. There is quite a bit of adhesive underneath the battery and the tab will normally just rip off or you can bend the battery. Instead, run your pry tool along the right side of the battery and break the adhesive that way. Once the battery is free from the adhesive, you can pull the battery out of the phone. There are no other connectors holding it in.

    4. You will notice a tiny grounding clip sitting underneath where you unscrewed the battery. Set this aside for replacement during reassembly. This is a grounding clip for your antenna. Make sure you put it back in place before reconnecting your battery.
Remove the dock connector shield and disconnect the cable

    1. There is a shield held on with two screws covering the dock connector cable. Remove the two screws holding it in place and set the shield and screws aside, remembering where they came from.

    2. Next, use your pry tool to pry up the actual dock connector cable. Be careful as there is adhesive holding the cable in place as well. Peel back the adhesive gently to free the cable.
Remove the top logic board shield

    There are 5 screws holding the logic board shield in place. Remove the 5 screws holding it in place. Just be sure to remember which holes they came out of as the screws are different sizes. I always keep them in order of how they came out.

    Next you’ll need to remove the shield. There is a tiny clip built into the shield holding it in place. (Refer to the photo above.) Pop it up with your pry tool and you should be able to slide the shield up fairly easily. Just take care not to bend it or break off a clip.
Disconnect the 6 cables from the top of the logic board

    There is only one connector holding the camera to the logic board. Remove this cable in the picture above using your pry tool. Gently lift upwards and it will pop right off.

    Next gently lift the camera out of the device. You’ll notice there is a tiny tab that is seated underneath the LCD and digitizer cables to the right.

    Next pop up the LCD and digitizer cables to the right of where the camera cable was connected. You pop them up in the same direction.

    The 3 cables further to the right will need to be disconnected as well. They pop up in the opposite direction.
Remove the logic board

    Start with the 2 screws holding the logic board down in the middle and at the bottom left. Both use your #00 Phillips screwdriver. They are the same size. The one on the right of the logic board in the middle of the device has a water sensor over it you’ll need to remove.
    The second screw is located where the logic board meets the speaker assembly towards the bottom left of the device.

    The third and final screw holding the logic board in is located at the top of the logic board off to the right. It is the only cross-head screw in your device. Use a small flathead screwdriver to carefully remove it.

    You should now be able to remove your logic board. Holding it at the bottom, gently pull it upwards. I use my other hand to lift up at the top where the rear facing camera used to be.
    Take note that there is a small rubber piece that sits at the top of the logic board. You will need this for re-assembly so make sure it doesn’t fall off. If you lose this, you could see reception issues.
Remove the speaker assembly

    1. To remove the speaker assembly you have one more #00 screw to remove. It sits to the right of the speaker assembly in the bottom right hand corner of your device. Remove it.
    2. The second screw holding the speaker assembly into your iPhone you’ve already removed when you removed the logic board.
    3. Gently lift the speaker assembly out of your device and set it aside.
Remove the vibrator assembly

    Locate your vibrator assembly in the upper right hand corner of your iPhone 4 (assuming you’re looking at it from the back).

    It is held in with two screws. Use your #00 Phillips screwdriver and remove them. The screw on the left will be significantly longer. Just remember which screw came from where.

    Next, gently lift the vibrator assembly out of the device.
Remove the 4 screws in each corner

There are 10 total screws that attach your iPhone 4 LCD/Digitizer assembly to your frame. The 4 in the corners will need to be completely removed. They are all #00 screws.
Loosen the remaining 6 screws

These screws run along the sides of your iPhone and also have washers on them. I find it best to just loosen them opposed to removing them completely. The washers are not fun to put back in. Loosening them will allow you to remove the LCD/Digitizer assembly just as easily. About 2 1/2 to 3 turns for each screw should loosen them up enough to continue. If you feel the washer wobbling back and forth a bit, you’ve loosened it enough.
Remove the broken LCD & digitizer assembly from your iPhone
This is where it can get a bit tricky. Your screen is held in not only with the 10 screws mentioned above but also with strong adhesive. You will need to break this adhesive in order to remove the front panel.

    Hold your iPhone in one hand with the screen facing you. Starting in the top left hand corner, run a pry tool or razor blade in between the frame and front panel. You’ll need to pry up quite a bit in order to break the adhesive. Be careful around the front facing camera and speaker area.

    Next move your pry tool or razor blade to the bottom of your device and do the same thing, working your way around until the adhesive is broken and the front panel starts to come off. If your screen is cracked, additional glass may break off. That’s perfectly normal.

    To completely remove the front panel – start at the top of your iPhone and gently pull the assembly away from the frame. Be careful to allow the LCD and digitizer cables to slip through the opening in the frame without getting caught up.
Remove any left over glass or debris from the frame
Before reassembling your iPhone, you’ll need to make sure there is no glass stuck to the remaining adhesive or inside the frame. If there is it could cause damage to the new screen or you’ll be able to see it through the new assembly, which can be annoying. Just make sure you do a thorough job of picking off all the glass on and around the frame before continuing to reassembly.
Reassemble your iPhone

Read more »

Pod2g Announces Corona Gonna Update 1.0.6 To Fix iBooks DRM Issues

Summary : iBooks goes not very well with jailbreaking... From the start, Apple has always patched iBooks so that it didn’t work with a jailbroken iDevice. In fact before the RedSn0w 0.9.10b5 was released, Pod2g has announced that Corona is gonna updated to fix issues with iBooks DRMd books.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

 

iBooks goes not very well with jailbreaking... From the start, Apple has always patched iBooks so that it didn’t work with a jailbroken iDevice. In fact before the RedSn0w 0.9.10b5 was released, Pod2g has announced that Corona is gonna updated to fix issues with iBooks DRMd books.
If you have been following the jailbreak scene, then you must know what Corona is. For those who don’t, Corona is the tool that lets you untethered jailbreak your iOS device (A4 only) on iOS 5.0.1. Pod2g is the hacker who worked on the Corona Untether and now he’s given an update on the case of the iBooks error. Corona 5.0.1 version 1.0-5 was released sometime back to fix the iBooks crash issue, but users even after applying the update have faced problems with iBooks. Certain users have been facing problems with digital rights management technology (DRM) protected content, wherein images and text tend to disappear.
Not to worry folks, because @planetbeing is at it again and according to @pod2g’s latest tweet, the Corona 1.0.6 update with the iBooks DRM content fix should be released soon.

We will update you as soon as the fix is out! Has anyone faced any such issues with iBooks on iOS 5.0.1 after jailbreaking?
via ijailbreak

Read more »

A4 Jailbreak RedSn0w Updated to 0.9.10b5 To Fix iBooks DRM Bug

Summary : It looks the iPhone Dev-Team have released an updated version of RedSn0w. This RedSn0w update brings RedSn0w to version 0.9.10b5 and integrates a utility called “crazeles” that overcomes Jailbreak detection by iBooks that would cause about 10% of images to show incorrectly.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

 

 

After It looks the iPhone Dev-Team have released an updated version of RedSn0w. This RedSn0w update brings RedSn0w to version 0.9.10b5 and integrates a utility called “crazeles” that overcomes Jailbreak detection by iBooks that would cause about 10% of images to show incorrectly.
"Redsn0w version b5 incorporates yet another fix for iBooks, this time involving DRM.  @planetbeing wrote a utility called “crazeles” that overcomes jailbreak detection by iBooks that would cause about 10% of images to show incorrectly.  This fix is similar to the “hunnypot” fix that @comex wrote for the 4.x jailbreak.  As usual, you can choose to install the fix either by re-running redsn0w over your existing jailbreak (de-select Cydia if you do that), or by installing the corona package from Cydia (it’s the same set of files no matter which way you choose)."
If you would like to Re-Jailbreak your iPhone, iPod Touch or iPad with RedSn0w 0.9.10b5 to apply the iBooks DRM fix you will simply need to go through the Jailbreaking process again, without selecting the Install Cydia Option. Of course you can also wait until the updated version of Corona is released with this iBooks DRM fix.
According to Pod2g Corona is gonna updated to 1.0.6 fix issues with iBooks DRMd books. For those of you who would like to download RedSn0w 0.9.10b5 you can use one of the direct links shown below.

Download RedSn0w 0.9.10b5 Windows

Download RedSn0w 0.9.10b5 Mac OS X

Let us know if you have any further questions or thoughts to do with RedSn0w 0.9.10b5 in the comments section below…
via ijailbreak

Read more »

10 iOS Games For The Jailbreaking Week

Summary : This is a significant week, the so expected untethered jailbreak for iPhone 4S and iPad 2 is finally here. Now you should arm your newly jailbroken device with new games. Here are 10 games we recommended best. Enjoy the jailbreaking and the gaming!

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

This is a significant week, the so expected untethered jailbreak for iPhone 4S and iPad 2 is finally here. Now you should arm your newly jailbroken device with new games. Here are 10 games we recommended best. Enjoy the jailbreaking and the gaming!
1.PES 2012 - Pro Evolution Soccer
Description
 You can play UNLIMITED MATCHES against your friends' SUPER CHALLENGE team using your own SUPER CHALLENGE team.
 QUICK MATCH is limited to one half time.
 An In-App purchase is necessary to unlock the following full feature set:
 Live the PES 2012 experience with your friends in the most connected edition of the best football game on smartphones! With two brand new games modes, full social networks integration, asynchronous and live multiplayer over wifi and Bluetooth: you will never play alone again.
 DISCOVER THE BRAND NEW SUPER CHALLENGE MODE
 Build your very own dream-team by purchasing the most wanted players in an on-going league. Want Ronaldo in your team? In PES 2012 you can!
 VICTORY IS SWEETER WHEN YOU KNOW YOUR RIVAL
 Defy your friends by downloading their Super Challenge teams online to play against on your iPhone or iPad and post the score on your Facebook to claim bragging rights.
 FOOTBALL GAMEPLAY AT ITS FINEST
 With an improved AI and goalkeepers behaviours, you will soon find out why expensive players are worth every penny with dedicated high-end animations and a complete set of stats.
 DIVE INTO THE FIELD IN COMPLETE IMMERSION
 With added crowd jeers and cheers, retina support, all new stadium, official UEFA Champions league™ and Europa League™, Liga BBVA, Ligue 1 and much, much more!
 DID YOU JUST SAY MORE?
 With a flurry of content such as classic national teams, 24 different balls, 6 varied environmental combinations such as rain and snow, exhibition mode and 3 different controls configurations: tinkering the perfect setup will never have been so fun.
 BIGGEST BANG FOR THE BUCK WITH UNIVERSAL APP
 Buy once and play on any of your iOS devices, the game automatically scales to accommodate even your older device. Have an iPad? Enjoy the stunning graphics of PES in native resolution without any additional cost!
 YOU WILL NEVER BE BORED AGAIN
 Two special modes dedicated for these moments when you just have a few minutes to kill, in Quick Play you’ll be kicking in less than a minute, and in the brand new Free Kick Challenge you’ll be able to surpass your shooting skills with effects and touchscreen accuracy!

download

Read more »

Chpwn Releases Update to Zephyr, Add New Gestures

Summary : The Zephyr Cydia tweak was recently updated to version 1.1, which includes some new gestures, improved stability and general bug fixes. It would be be useful if you have a broken home button on your iOS device.

• PandaApp Editor

• Current Device: HTC Chacha
• Future Device: iPhone 5.6.7.8...iPad 2.3.4.5...
• Introduction:Tracing new technology like fashion!

Zephyr Cydia tweak that was developed by Chpwn. Released back in December of 2011, Zephyr modifies the way you switch between applications and enable the multitasking bar. With the Zephyr Cydia tweak you can bring up the multitasking bar by simply swiping up from the bottom of your screen to the top of the screen. This tweak also allows you to switch between applications by simply sliding right to left or left to right on your iOS devices screen. Zephyr can also be useful if you have a broken home button on your iOS device.
The Zephyr Cydia tweak was recently updated to version 1.1, which includes some new gestures, improved stability and general bug fixes.
Features:
● Swipe up from the bottom of the screen to close apps.
(Perfect for a broken home button!)
● Switch apps simply by swiping left or right from the edge.
● Smoothly swipe up to see your multitasking switcher.
● The best way to really multitask.

What's New in Version 1.1:
● Swipe up to close apps!
● Pause while swiping up to show the switcher.
● Swipe to the next app immediately from the side.
● Fix bugs; improve performance.
● Remove conflict with the latest Multicleaner.
If you are interested in downloading the Zephyr Cydia tweak to your iPhone, iPod Touch or iPad, you can download it from the BigBoss repo for a price of $2.99.
For a more detailed look at Zephyr v1.1 take a look at the YouTube video below…

via iclarified via ijailbreak

Read more »